Feature Articles: Access Network Technologies for IOWN

Vol. 20, No. 9, pp. 40–46, Sept. 2022. https://doi.org/10.53829/ntr202209fa5

50 Years at Tsukuba R&D Center

Hiroshi Takahashi, Hideo Kawata, Ryo Koyama,
Ryo Tanaka, Shinya Otsuki, Kazuto Goto,
and Masashi Tadokoro

Abstract

NTT Access Network Service Systems Laboratories was established in Tsukuba City on July 20, 1972 as Tsukuba Telecommunication Construction Engineering Development Center. Since then, it has been renamed several times during the era of the Nippon Telegraph and Telephone Public Corporation and the Nippon Telegraph and Telephone Corporation (NTT). In July 2022, the Laboratories’ Tsukuba Research and Development (R&D) Center celebrated its 50th anniversary. This article introduces the 50-year history of the Tsukuba R&D Center, focusing on the large-scale experimental facilities that supported R&D activities in Tsukuba.

Keywords: access network, infrastructure, optical fiber

PDF

1. Introduction

Tsukuba Telecommunication Construction Engineering Development Center of the Nippon Telegraph and Telephone Public Corporation, the predecessor of NTT Access Network Service Systems Laboratories, was established in July 1972 as a member of the 43 research and educational institutions planned for the Tsukuba Science City, a national project promoted by Cabinet approval in September 1963 [1]. As shown in Fig. 1, Tsukuba Telecommunication Construction Engineering Development Center was reorganized into Tsukuba Engineering Development Center (1985), Tsukuba Field Engineering Development Center (1987), NTT Telecommunication Field Systems Research and Development (R&D) Center (1991), and NTT Access Network Systems Laboratories (1994) and took its current name of NTT Access Network Service Systems Laboratories in January 1999. The Tsukuba R&D Center was established as the organization’s experimental facilities in 1972, and the Makuhari Building and Yokosuka R&D Center were added to the organization in 1997, and the Musashino R&D Center was added in 2014. In July 2022, NTT Access Network Service Systems Laboratories and its Tsukuba R&D Center celebrated their 50th anniversary.


Fig. 1. History of NTT Access Network Service Systems Laboratories.

When it was first established as Tsukuba Telecommunication Construction Engineering Development Center, R&D activities on metal access technology and infrastructure technology were conducted in Tsukuba to improve the efficiency, safety, and work environment of outdoor construction work due to the increase in telephone service demand at that time. NTT Access Network Service Systems Laboratories is currently conducting R&D in the five fields of optical-fiber access technology, infrastructure technology, access system technology, wireless access technology, and operation technology. At the Tsukuba R&D Center, our R&D has been focused on communication lines and civil engineering facilities since the establishment of Tsukuba Telecommunication Construction Engineering Development Center.

The Tsukuba R&D Center was designed to conduct various experiments under conditions equivalent to those in the field to create communication facilities that can work in various environments. Therefore, it has large-scale and unique experimental equipment and facilities for communication lines and civil engineering facilities. This article describes the large-scale experimental equipment and facilities that support the R&D in Tsukuba.

2. Large-scale experimental equipment and facilities at Tsukuba R&D Center

The Tsukuba R&D Center has mainly been carrying out R&D on infrastructure technology, metal access technology, and optical-fiber access technology. This article focuses on the facilities that were constructed during the Tsukuba Telecommunication Construction Engineering Development Center era but have now completed their intended purposes.

Figure 2 shows the facilities of the Tsukuba R&D Center in 1983 and the current ones on the vast site of about 22 hectares. Many of the facilities were designed to accurately reproduce installation environments such as the high-rise laboratory building (a vertical wiring experiment facility and was the highest in the world), buried object experiment facility by soil type, shield propulsion experimental facility, underwater experimental equipment, cable weather conditioning experiment facility, and vibration fatigue experiment equipment.


Fig. 2. Large-scale experimental equipment and facilities at Tsukuba R&D Center.

Figure 3 shows photographs of the high-rise laboratory building at the time of its completion (1983). With the increase in high-rise buildings, such as skyscrapers and large bridges, it was constructed for the purpose of improving vertical cable-laying methods and elucidating temperature changes in high-rise facilities and seismic behavior of high-rise facilities during earthquakes. Inside the building, there was a 75-m-high, 1.8-m-long, and 2.5-m-wide shaft (A) (from the 3rd story below ground to 12th story above ground) for cable laying experiments, static load tests, and vibration tests, and a 60-m-high, 1.0-m-long, and 1.0-m-wide shaft (B) (from the 1st story above ground to 12th story above ground) for vertical cable heat cycle tests (–40 to +80°C). It was used to verify the vertical installation of various cables. Today, vertically optical wiring installations are common in high-rise buildings, and their reliability is widely recognized and unshakable. The purpose of this experimental facility was accomplished, thus it was dismantled.


Fig. 3. High-rise laboratory building.

Figure 4 shows the large-scale experimental facilities used for verification of underground facilities and underwater communication lines and civil engineering facilities. Figure 4(a) shows photographs of the buried object experiment facility by soil type at the time of completion (1977). This facility was constructed to replicate installation under roads for the purpose of examining issues such as design, construction, and maintenance, because ground properties are diverse and difficult to predict accurately. The facility made it possible to alter soil quality, groundwater level, etc., and run a load car reproducing automobile loads over it. It was useful in various verification tests, such as the investigation of the effect of burying a full-scale manhole, and the investigation of the movement of optical fiber cable in the pipeline by burying a pipeline in the soil layer close to the actual site and driving a load car over it. Underground facilities for communication services have been installed all over Japan, thus this facility completed its intended purpose.


Fig. 4. Large-scale experimental facilities used for verification of underground and underwater facilities.

Figure 4(b) shows the test pit and panoramic view of the shield propulsion experimental facility. To apply the shield-tunneling method developed for road construction without using open pit methods, this facility was constructed to verify the adaptability and safety of the method, considering various construction conditions expected at different sites. By putting a sample of the soil layer under test into the pressure soil tank and using a water-pressure generator to apply arbitrary water pressures to the layer, predetermined ground conditions could be created. Therefore, a small model shield machine installed in the experimental pit was propelled into the soil layer, and experiments on excavation, soil removal, etc. were conducted. As the shield-tunneling method for various types of ground has become widely used, and the construction of new roads has been reduced, the shield propulsion experimental facility was dismantled upon completion of its purpose.

Figure 4(c) shows an exterior view of the underwater experimental equipment at the time of completion (1974). It was constructed to test the laying of submarine cables and water-resistance tests of underground structures. It consisted of a water tank 50 m long, 6 m wide, and 5 m deep, underwater observation tunnel, moving bridge, bridge crane, and measurement room. The mobile bridge was self-propelled with a running speed of 10–50 m/min and used as a simulated submarine-cable laying device for conducting simulation experiments on submarine cables. Test methods for submarine cables and underground facilities were established, therefore this equipment has been removed.

Figure 5 shows the large-scale experimental facilities used for the verification of aerial communication cables and civil engineering facilities in the open. Figure 5(a) shows the cable weather conditioning experiment facility at the time of completion (1973). Since most communication lines and civil engineering facilities are installed outdoors, this facility was constructed to reproduce actual cable installation environments and conduct weatherability tests and temperature-characteristic tests. Having a totally stainless steel roof and being 150 m long, 2.45 m wide, and 2.25 m high, it made it possible to reproduce in a test room the state of installation in a conduit, pipeline, and on a telephone pole. At the time of construction, the temperature could be changed from –20 to +60°C, but now it can be changed from –30 to +70°C. In optical cables, small bends in the cable affect various transmission characteristics, so we will continue to use the facility through various tests for the practical application of new fiber and cable structures.


Fig. 5. Large-scale experimental facilities used for verification of aerial communication cables and civil engineering facilities in the open.

Figure 5(b) shows the vibration fatigue experiment equipment when it was completed (1977). It was constructed for the purpose of clarifying the response characteristics, such as the increase in optical loss and fracture of cables, passive optical components, closures, and hardware, used in overhead lines by the imposition of vibration to replicate the effect of wind on aerial cables, etc. By providing feedback to the design, development, and verification of new cables and components, we have been able to enable safe long-term use of overhead equipment and facilities. This equipment can forcibly excite cables and suspended wires with actually installed aerial cables. At the time of completion, the maximum installation length was 35 m, but the maximum installation length has been extended to 65 m, and it will continue to be used for various experiments.

As of 2022, we also have large-scale experimental facilities intended to support the Innovative Optical and Wireless Network (IOWN) and smart facilities, as shown in red in Fig. 2.

3. Summary

This article introduced the R&D history of the Tsukuba R&D Center over the last 50 years, focusing on the large experimental equipment and facilities created to support the R&D of communication lines and civil engineering facilities. We will continue to conduct R&D activities toward the development of smart facilities that support IOWN, with the aim of achieving technologies that can be used to support both the most advanced in the world and easy-to-use in the field.

Reference

[1] Website of Ministry of Land, Infrastructure, Transport and Tourism, Tsukuba Science City,
https://www.mlit.go.jp/crd/daisei/tsukuba/english/index.html
Hiroshi Takahashi
Senior Research Engineer, Access Network Management Project, NTT Access Network Service Systems Laboratories.
He received a B.E. in electrical engineering from Tokyo University of Science in 2008 and an M.E. in electrical engineering and information systems from the University of Tokyo in 2010. He joined NTT Access Network Service Systems Laboratories in 2010, where he has been engaged in research on advanced optical measurements and optical fiber network evaluation. He is currently a senior research engineer in a research group developing advanced optical measurements for optical fiber network management and optical fiber sensing. He is a member of the Institute of Electronics, Information and Communication Engineers (IEICE) of Japan.
Hideo Kawata
Senior Research Engineer, Optical Access Systems Project, NTT Access Network Service Systems Laboratories.
He received a B.S. and M.S. from the College of Science and Technology, Nihon University, Tokyo, in 1996 and 1998, and Ph.D. in engineering from Utsunomiya University, Tochigi, in 2009. In 1998, he joined NTT Access Network Service Systems Laboratories, where he was engaged in research on wavelength-division-multiplexed access systems. He is currently engaged in research on Time-Sensitive Networking.
Ryo Koyama
Senior Research Engineer, Access Network Media Project, NTT Access Network Service Systems Laboratories.
He received a B.S. and M.S. in precision engineering from the University of Tokyo in 2001 and 2003. In 2003, he joined NTT Access Network Service Systems Laboratories, where he has been engaged in research on optical fiber wiring and splicing techniques for optical access networks. He is an assistant secretary of the International Electrotechnical Commission (IEC) Subcommittee 86B and member of IEICE.
Ryo Tanaka
Senior Research Engineer, Civil Engineering Project, NTT Access Network Service Systems Laboratories.
He received a B.E. from the Department of Geophysics, Tohoku University, Miyagi, in 2001 and M.E. from the Department of Earth and Planetary Science, the University of Tokyo in 2005. He joined NTT WEST in 2005 and joined NTT Network Innovation Laboratories in 2021. He is presently developing technology for extending service life of structures at NTT Access Network Service Systems Laboratories.
Shinya Otsuki
Senior Research Engineer, Wireless Access Systems Project, NTT Access Network Service Systems Laboratories.
He received a B.E., M.E., and Ph.D. in communication engineering from Osaka University in 1993, 1995, and 1997. He joined NTT in 1997. From 1997 to 2008, he studied wireless access systems, wireless local area network systems, and wireless systems for Internet services in trains. From 2008 to 2011, he was involved in international standardization efforts in evolved packet core and services using Internet Protocol multimedia subsystems at NTT Service Integration Laboratories. He has been with NTT Access Network Service Systems Laboratories since 2011 and has been contributing to the activities of Working Parties 5A and 5C in Study Group 5 of the International Telecommunication Union (ITU) Radiocommunication Sector. He received the Young Engineer Award from IEICE in 2004 and the ITU-AJ International Activity Encouragement Award and the ITU-AJ Accomplishment Award from the ITU Association of Japan in 2014 and 2022, respectively. He is a member of the Institute of Electrical and Electronics Engineers (IEEE) and IEICE.
Kazuto Goto
Senior Research Engineer, Wireless Entrance Systems Project, NTT Access Network Service Systems Laboratories.
He received a B.E. and M.E. in knowledge engineering and computer sciences from Doshisha University, Kyoto, in 2006 and 2008 and Ph.D. from the Graduate School of Science and Engineering, Doshisha University, in 2020. He joined NTT Network Innovation Laboratories in 2008. He is currently developing wireless communication using high-frequency bands at NTT Access Network Service Systems Laboratories. He is a member of IEICE.
Masashi Tadokoro
Senior Research Engineer, Access Network Operation Project, NTT Access Network Service Systems Laboratories.
He received an M.E. in nuclear engineering from the University of Tokyo in 2004 and joined NTT the same year. He has 13-year experience in R&D activity of optical access networks including radio-over-fiber technology and Ethernet-based passive optical network technology. His current research involves operation support technology based on software for access networks.

↑ TOP